PIC18F46J11 FAMILY
DS39932D-page 178
2011 Microchip Technology Inc.
11.1.2
DATA REGISTERS
The PMP module uses eight registers for transferring
data into and out of the microcontroller. They are
arranged as four pairs to allow the option of 16-bit data
operations:
PMDIN1H and PMDIN1L
PMDIN2H and PMDIN2L
PMADDRH/PMDOUT1H and PMADDRL/PMDOUT1L
PMDOUT2H and PMDOUT2L
The PMDIN1 register is used for incoming data in Slave
modes and both input and output data in Master
modes. The PMDIN2 register is used for buffering input
data in select Slave modes.
The PMADDR/PMDOUT1 registers are actually a
single register pair; the name and function are dictated
by the module’s operating mode. In Master modes, the
registers function as the PMADDRH and PMADDRL
registers and contain the address of any incoming or
outgoing data. In Slave modes, the registers function
as PMDOUT1H and PMDOUT1L and are used for
outgoing data.
PMADDRH differs from PMADDRL in that it can also
have limited PMP control functions. When the module is
operating in select Master mode configurations, the
upper two bits of the register can be used to determine
the operation of chip select signals. If these are not
used, PMADDR simply functions to hold the upper 8 bits
of the address. Register 11-9 provides the function of
the individual bits in PMADDRH.
The PMDOUT2H and PMDOUT2L registers are only
used in Buffered Slave modes and serve as a buffer for
outgoing data.
11.1.3
PAD CONFIGURATION CONTROL
REGISTER
In addition to the module level configuration options,
the PMP module can also be configured at the I/O pin
for electrical operation. This option allows users to
select either the normal Schmitt Trigger input buffer on
digital I/O pins shared with the PMP, or use TTL level
compatible buffers instead. Buffer configuration is
controlled by the PMPTTL bit in the PADCFG1 register.
相关PDF资料
DSPIC30F4011-30I/ML IC DSPIC MCU/DSP 48K 44QFN
DSPIC30F4013-30I/ML IC DSPIC MCU/DSP 48K 44QFN
DSPIC30F5013-30I/PT IC DSPIC MCU/DSP 66K 80TQFP
DSPIC30F5015-30I/PT IC DSPIC MCU/DSP 66K 64TQFP
DSPIC30F6010-20E/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F6010A-30I/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F6013A-30I/PF IC DSPIC MCU/DSP 132K 80TQFP
DSPIC30F6014-30I/PF IC DSPIC MCU/DSP 144K 80TQFP
相关代理商/技术参数
dsPIC30F3013-20I/SO 功能描述:数字信号处理器和控制器 - DSP, DSC 28LD 20MIPS 24 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC30F3013-20I/SP 功能描述:数字信号处理器和控制器 - DSP, DSC 28LD 20MIPS 24 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F3013-30I/ML 功能描述:数字信号处理器和控制器 - DSP, DSC Sensor RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F3013-30I/SO 功能描述:数字信号处理器和控制器 - DSP, DSC Sensor RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F3013-30I/SO 制造商:Microchip Technology Inc 功能描述:IC DSC 16BIT 24KB 40MHZ 5.5V SOIC-28
DSPIC30F3013-30I/SP 功能描述:数字信号处理器和控制器 - DSP, DSC Sensor RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F3013-30I/SP 制造商:Microchip Technology Inc 功能描述:16-Bit Digital Signal Controller
dsPIC30F3013T-20E/ML 功能描述:数字信号处理器和控制器 - DSP, DSC 44LD 20MIPS 24 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT